Master Class

Master Class | Sunday, April 11, 2021 | United States



Purging Stainless Steel Tubing

By Scott Skrjanc, former Lincoln Electric welding instructor and current group leader

Back Purging Stainless Steel

Stainless steel is the preferred material in many applications because of its resistance to corrosion.

When preparing to weld a stainless steel pipe, purging is an important step to ensure that the weld is successful and that it remains intact for the long term.

While our demonstration involves a vehicle exhaust tube, purging stainless steel is important when welding pipe for food storage and other applications where impurities must be avoided. For example, failure to purge a pipe that transports food or beverage materials could lead to particles becoming trapped in hard-to-clean grooves, resulting in contamination.

On the outside, a weld on purged and non-purged stainless steel pipe looks identical. On the inside, however, is where the important difference occurs.

A purged weld is flat and tied in on the inside where the weld metal comes together. There are no valleys that could potentially threaten the integrity of the weld. Both portions of the tube look exactly alike.

A non-purged tube displays a “sugaring effect” resulting from the presence of chromium oxide. The presence of oxygen in the weld seam results in oxidation. A noticeable line forms where the weld metal comes together because it doesn’t fuse well. Non-purged stainless steel could crack, especially in high-vibration conditions. Caustic materials could become wedged in the line and eat away at the weld.

Purging removes oxygen and nitrogen and replaces those gases with a 100% argon gas atmosphere.

So to ensure the integrity of the weld, purging is an important part of the process when connecting (or repairing) stainless steel pipe.

image

The process starts with an examination of the pipe you intend to weld. It can be partially or completely separated. There may be one or multiple cracks. If it is partially separated, it’s good to leave it that way (as opposed to breaking it into two pieces) because the fit will be much better.

A good cleaning of the tube is always recommended. Remember, TIG does not like dirty material. Make sure you clean the inside of the pipe if you have access to it. At the very least, clean the outside.

Safety is always a primary concern when welding. Make sure you’re welding in a well-ventilated area and wearing personal protective equipment. Once the work area is prepared, you can set up and begin the purge.

After cleaning, tape off one end completely with masking or other adhesive tape, then punch several holes in the tape to allow the oxygen and nitrogen inside to escape (we used a TIG rod for this; see Figure A). Place the purge hose with gas lens (to help with the gas flow) into the other end of the tube and tape off that side completely as well (see Figure B). This prevents the reintroduction of oxygen and nitrogen into the pipe.

Set the regulator (dual flow or separate tanks) to run 15 to 20 CFH of argon to initiate the purge. You’ll know the purge process is happening when you feel the gas escaping the perforated end of the pipe. You also want the argon on the outside of the tube.

The length of time to purge prior to beginning to weld is based on the pipe’s diameter. Make sure the argon continues to flow during the entire welding process.

When you’re ready, place several tack welds around the pipe.

When it’s time for the final weld, the amperage should be based on the thickness of the tube. A general rule is 1 amp per thousandths of an inch. For example, a tube 0.035 thick requires 35 amps. Stainless steel is welded on DC negative.

Once the weld is complete, let it cool naturally.

Welding stainless steel is not difficult, but it does take practice—and so does purging. Weld on purged and non-purged materials to see the difference for yourself. Purging creates the best possible weld environment and ensures that the metal joins properly and stays together.

image
image
image
image

Tools

• 304L tubing
• Lincoln® ER308/308L filler rod
• Lincoln Electric
Precision TIG® 225 Welder, DC Negative
• Tungsten
• Argon gas
• Purge line with gas lens
• Dual-flow regulator

Personal Protective Equipment

• Safety glasses
• Gloves
• Sleeves
• Helmet
• Well-ventilated area

image